Copying Glemco© content is not allowed.

Delrin® 150

Material Information

Find Material Matches For Your Project

Specifications

Physical PropertiesMetricEnglishComments
Specific Gravity1.42 g/cc1.42 g/ccASTM D 792
Water Absorption0.25% @Time 86400 Sec0.25% @Time 24.0 HourASTM D 570
Moisture Absorption at Saturation0.90%0.90%ASTM D 570
Mechanical PropertiesMetricEnglishComments
Hardness, Rockwell M9494ASTM D 785
Hardness, Rockwell R120120ASTM D 785
Tensile Strength, Yield75.8 MPa11000 psiASTM D 638
Elongation at Break25 %25 %ASTM D 638
Tensile Modulus3.10 GPa450 ksiASTM D 638
Flexural Strength110 Mpa16000 psiASTM D 790
Flexural Modulus2.90 GPa420 ksiASTM D 790
Compressive Strength35.9 MPa5200 psiASTM D 695
Izod Impact, Unnotched0.80 J/cm1.5 ft-lb/inASTM D 256
Coefficient of Friction, Dynamic0.20.240 psi, 50 fpm; ASTM D 3702
K (wear) Factor111 x 10-8 mm³/N-M55.0 x 10-10 in³-min/ft-lb-hr ASTM D 3702
Limiting Pressure Velocity0.0513 MPa-m/sec1460 psi-ft/min ASTM D 792
Electrical PropertiesMetricEnglishComments
Volume Resistivity1.00e+15 ohm-cm1.00e+15 ohm-cm ASTM D 257
Dielectric Constant3.7 @ Frequency 60.0 Hz3.7 @ Frequency 60.0 Hz50% RH; ASTM D 150
Dielectric Strength19.7 kV/mm500 kV/inASTM D 149
Dissipation Factor0.0050 @ Frequency 60.0 Hz0.0050 @ Frequency 60.0 HzASTM D 150
Thermal PropertiesMetricEnglishComments
CTE, linear 122 µm/m-°C68.0 µin/in-°F ASTM D 696
Melting Point175 °C347 °FASTM D 2133
Maximum Service Temperature, Air85.0 °C185 °FContinuous; UL746B
Maximum Service Temperature, Air149 °C300 °F Intermittent
Deflection Temperature at 0.46 MPa (66 psi)169 °C336 °FASTM D 648
Deflection Temperature at 1.8 MPa (264 psi)125 °C257 °FASTM D 648
Flammability, UL94HBHBUL94

NOTE: The information in this data sheet is for design guidance only. Forming methods and specific geometry could affect properties.

Overview

Delrin® acetal homopolymer (Polyoxymethylene POM) is the ideal material in parts designed to replace metal. It combines low-friction and high-wear resistance with the high strength and stiffness such applications require. It provides a wide operating temperature range (-40 °C to 120 °C) and good colorability. Also, it mates well with metals and other polymers and offers excellent dimensional stability in high precision molding, greater tensile strength, stiffness, creep and fatigue resistance, as well as significantly higher impact resistance. The combination of these excellent mechanical properties in a single material allows for thinner, lighter-weight parts and shorter molding cycles with potential cost reductions. Material data provided by Dupont and Ensinger Plastics.

Applications & Usage

  • Mounting Insulators
  • Shield Bushings
  • Fittings
  • Washers
  • Gears
  • Conveyor System parts
  • Safety Restraint components
  • Medical Delivery devices
  • Zip Fasteners
  • Appliance parts such as bearings, bushings, and rollers
  • Sports Equipment

Industries Using This Material

Semiconductor

One of the original second source providers, Glemco has been manufacturing products in the US in support of the semiconductor industry for over 40 years. Our extensive history means that we can support the oldest legacy equipment or the newest cutting-edge implant technology, with available upgrades and enhancements to drive efficiency, reliability and performance improvements.

Semiconductor

One of the original second source providers, Glemco has been manufacturing products in the US in support of the semiconductor industry for over 40 years. Our extensive history means that we can support the oldest legacy equipment or the newest cutting-edge implant technology, with available upgrades and enhancements to drive efficiency, reliability and performance improvements.
Learn More

Packaging

We can support emergency repair, produce a legacy part from your sample, and stock high wear parts no longer supported by the OEM. Our expert team can also help you bring your packaging design concept to reality.

Packaging

We can support emergency repair, produce a legacy part from your sample, and stock high wear parts no longer supported by the OEM. Our expert team can also help you bring your packaging design concept to reality.

Pharmaceutical

CNC machining is critical to delivering the precision and value required for success in manufacturing pharmaceutical equipment and replacement parts. Quality, precision and efficiency are always our priorities.

Pharmaceutical

CNC machining is critical to delivering the precision and value required for success in manufacturing pharmaceutical equipment and replacement parts. Quality, precision and efficiency are always our priorities.

Specialists with 40 years’ experience in manufacturing high quality products for a global market.

Facebook
Linkedin
Instagram
Youtube

Contact Us

Address: 901 CR 270, Leander, TX 78641
Email: sales@glemco.com

Main: 512.259.0320
Toll Free: 800.621.9598
Fax: 512.259.5101

Copyright © 2020 Glemco. All rights reserved.  |  Privacy Policy

Close Menu

Glemco Privacy Policy

Glemco, Inc. operates the www.glemco.com website, which provides the SERVICE. This page is used to inform website visitors regarding our policies with the collection, use, and disclosure of Personal Information if anyone decided to use our Service, the Glemco website. If you choose to use our Service, then you agree to the collection and use of information in relation with this policy. The Personal Information that we collect are used for providing and improving the Service. We will not use or share your information with anyone except as described in this Privacy Policy. The terms used in this Privacy Policy have the same meanings as in our Terms and Conditions, which is accessible at www.glemco.com, unless otherwise defined in this Privacy Policy. Our Privacy Policy was created with the help of the Privacy Policy Template and the Privacy Policy Generator from TermsFeed  plus the Refund Policy Template.

Information Collection and Use – For a better experience while using our Service, we may require you to provide us with certain personally identifiable information, including but not limited to your name, phone number, and postal address. The information that we collect will be used to contact or identify you.

Log Data – We want to inform you that whenever you visit our Service, we collect information that your browser sends to us that is called Log Data. This Log Data may include information such as your computer’s Internet Protocol (“IP”) address, browser version, pages of our Service that you visit, the time and date of your visit, the time spent on those pages, and other statistics.

Cookies – Cookies are files with small amount of data that is commonly used an anonymous unique identifier. These are sent to your browser from the website that you visit and are stored on your computer’s hard drive. Our website uses these “cookies” to collection information and to improve our Service. You have the option to either accept or refuse these cookies, and know when a cookie is being sent to your computer. If you choose to refuse our cookies, you may not be able to use some portions of our Service.

Service Providers – We may employ third-party companies and individuals due to the following reasons:

To facilitate our Service;
To provide the Service on our behalf;
To perform Service-related services; or
To assist us in analyzing how our Service is used.

We want to inform our Service users that these third parties have access to your Personal Information. The reason is to perform the tasks assigned to them on our behalf. However, they are obligated not to disclose or use the information for any other purpose.

Security – We value your trust in providing us your Personal Information, thus we are striving to use commercially acceptable means of protecting it. But remember that no method of transmission over the internet, or method of electronic storage is 100% secure and reliable, and we cannot guarantee its absolute security.

Links to Other Sites – Our Service may contain links to other sites. If you click on a third-party link, you will be directed to that site. Note that these external sites are not operated by us. Therefore, we strongly advise you to review the Privacy Policy of these websites. We have no control over, and assume no responsibility for the content, privacy policies, or practices of any third-party sites or services.

Children’s Privacy – Our Services do not address anyone under the age of 13. We do not knowingly collect personal identifiable information from children under 13. In the case we discover that a child under 13 has provided us with personal information, we immediately delete this from our servers. If you are a parent or guardian and you are aware that your child has provided us with personal information, please contact us so that we will be able to do necessary actions.

Changes to This Privacy Policy – We may update our Privacy Policy from time to time. Thus, we advise you to review this page periodically for any changes. We will notify you of any changes by posting the new Privacy Policy on this page. These changes are effective immediately, after they are posted on this page.

Contact Us – If you have any questions or suggestions about our Privacy Policy, do not hesitate to contact us.

Measurement & Inspection Equipment

  • • Coordinates Measurement
  • • Optical Comparators
  • • Leak Check System
  • • Pressure Test System
  • • Height Gauges
  • • Surface Comparators & Plates
  • • Hardness Testers
  • • Digital Calipers
  • • Vernier Calipers
  • • Precision Squares
  • • Inside & Outside Micrometers
  • • Thread Micrometers
  • • Depth Micrometers
  • • Blade Micrometers
  • • Hole Micrometers
  • • Sine Bar and Angle blocks
  • • Torque Wrenches
  • • Gage Block & Pin Sets
  • • Bore Gages
  • • Chamfer Gages
  • • Indicators
  • • Refractometers
  • • Ring & Outside Gages
  • • Thickness Gages
Milling2
5Axis2
Machine User Interface

Milling Machinery

Positional and dynamic 5 axis machining centers, up to x= 60” y= 26” z= 24”
High speed drilling and tapping centers, up to x=24” y=15.75” z=24”
Vertical machining centers, up to x=24” y=12” z=12”

Turning Tools

2 axis, max diameter 9”, max thru spindle diameter 2”, Max length 22”
4 axis with live tooling, max diameter 14”, max thru spindle diameter 3”, Max length 24”
5 axis with live tooling, max diameter 9”, max thru spindle diameter 2.6”, Max length 4.7”

Wire EDMs

Max part size x=41” y= 32.25” z= 11.75”
Max cutting capacity x=23.5” y= 15.5” z= 12”

CNC Sheet Metal Forming Machinery

Precision 36 ton, 6 axis control press brake, 48” length, 4” stroke, 10” throat depth

Versatility & Support Tools

Mills and lathes
Surface grinders
Hydraulic presses
Sheet metal shears
Horizontal and vertical band saws
Indexers/Rotary tables
Kilns
Blue M Ovens

National Women Business Owners Corporation Certified

Glemco has met all necessary criteria for NWBOC certification. Liana Merriman is the controlling business owner and is the final decision maker to employees, supervisors and managers. Her control spans all management of the business including sales, production and financial operations. Partners, vendors and suppliers can be confident that Glemco is indeed a woman owned company. View our NWBOC Certificate.

Proud To Be An ISO 9001: 2015 Certified Company

Glemco appreciates that the customer is our business. We embrace ISO as a management tool, and believe that only by embracing the concepts of Total Quality Management can we best service our customers. Glemco is committed to total customer satisfaction, achieved through innovative solutions to our customer’s needs. We strive to offer the highest quality product with continual improvement of manufacturing processes, service, and delivery. View our ISO 9001: 2015 Certificate.